Getting Started with Plumbing Basics for Bathtub Installation
Getting Started with Plumbing Basics for Bathtub Installation
Blog Article
What are your thoughts about Tools You Need to Install a New Bathtub ?
Installing a tub isn't exactly rocket science, however it does require strong plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a reasonably challenging job. If the old bathtub is easily easily accessible, the project can relocate immediately; if you have to open up a wall surface to get rid of the old tub as well as place the new bath tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will certainly require an assistant to move out the old tub and also set in the new one. Make sure you have actually qualified on your own for the work and also are comfortable attempting it. As opposed to employing a professional to take over a halfway-completed project, it is far better to consider using one before you begin. Opportunities are you might need an expert plumber to make tube links.
This short article will help you mount a new bath tub in your washroom if you have currently bought a brand-new bathtub and also do not need to change the setup of your previous water supply pipelines.
Your tools and product checklist should consist of the following:
Planning for the Installation
To start with, the supporting structure supplied with the bath needs to be fitted (if required) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is essential to make sure that if the tap includes a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets device to stop strain on the bath tub.
Fit the adaptable tap adapters to the bottom of both faucets making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you utilize every one of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be suited its last position.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the water system. After doing so, turn on the taps to drain any kind of water remaining in the system. The process of getting rid of the existing taps can be fairly bothersome because of the restricted gain access to that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a towel all set for the remaining water that will come from the pipelines. Once the supply pipes have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from turning during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Tub
Using the two wood boards under its feet, put the tub in the called for setting. The wooden boards are helpful in uniformly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little points.
The following goal is to ensure that the bathtub is leveled all round. This can be achieved by examining the level and also readjusting the feet on the tub up until the level reads degree.
To set up faucets, fit all-time low of the furthest adaptable faucet connector to the suitable supply pipe by making a compression sign up with; then do the very same for the various other tap.
Switch on the water supply and also examine all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill the bath tub as well as additionally inspect the overflow electrical outlet and also the normal electrical outlet for leaks.
Finally, fix the bath paneling as defined in the producer's user's manual. Tiling and securing around the bath tub must wait until the bathtub has been utilized at least when as this will certainly settle it right into its final position.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin making sure that the washers are in place between the faucet and also the sink. Safeguard the faucet in position with the manufacturer supplied backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular faucet ports. The previous kind needs to be attached to the faucet ends first, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the fitting can move enough to crack a stiff seal, causing the water to penetrate the wall surface in between the bathroom and also the tiling, leading to issues with dampness as well as possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes and cartridges, and are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of soaked paper or soft rope. Remember to always load the tub with water prior to sealing, to enable the activity experienced when the bathtub remains in usage. The sealer can break relatively early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also conveniently offered on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very interested in A Step-by-Step Guide to Installing a Bathtub and I am assuming you enjoyed reading the new post. Remember to take the opportunity to promote this content if you liked it. Thank-you for your time invested reading it.
Urgent plumbing? Call. Report this page